|
Summary https://www.thingiverse.com/thing:1514145 [size=14.6667px]If you have a question, first search in the Comments section. If you can't find an answer, then ask in a Comment. I will answer as fast and as much as I can. [size=14.6667px]And please, share your makes! Updates[size=14.6667px]20171118 New video by 3D Make [size=14.6667px]20171112 New "Assembly" and "Extensions and Derivatives" sub-sections in the "How-to". [size=14.6667px]20160910 Alternative Z stage that uses metal LM6UU linear bearings. The bearings should snap in their receptacles. Tinkercad model is here. [size=14.6667px]20160614 New Z stage, now integrated into the Y end. Unimaginatively called "v2". Same gear, same pen holder, a bit stronger, a bit better (one less part, less screws). [size=14.6667px]Print these: - drawing_machine_y_end2_v2.obj, and
- drawing_machine_z_stage_face_v2.obj
[size=14.6667px]To replace these: - drawing_machine_y_end2.obj,
- drawing_machine_z_stage.obj, and
- drawing_machine_z_stage_face.obj.
[size=14.6667px]20160505 updated some searches in the grocery list Summary[size=14.6667px]Please read Misan's instructions as well. [size=14.6667px]The Z stage does not use a servo, as in Misan's machine, but rather one of those cheap 28BYJ stepper motors you can find for 1.50$ on eBay. [size=14.6667px]NOTE: The photos are of the current prototype, some of the modifications to the various bits and pieces have not yet been tested. [size=14.6667px]This thing was made with Tinkercad. Edit it here.
Print Settings[size=14.6667px]Printer: [size=14.6667px]Wanhao i3 Duplicator
[size=14.6667px]Resolution: [size=14.6667px]0.2 mm
[size=14.6667px]Infill: [size=14.6667px]15% minimum
[size=14.6667px]Notes: [size=14.6667px]The Y end stops take a lot of tension from the belt. Making them as strong as possible to prevent flexing is not a bad idea.
Overview and Background[size=14.6667px]Overview [size=14.6667px]The drawing machine is a small three axis robot that controls a pen or any drawing implement over a canvas. It is a complete open source design and aims to teach the basics of robotics.
Budget for one is about 80$. You will need a 3D printer. Lesson Plan and Activity[size=14.6667px]See below Duration of Lesson[size=14.6667px]40 hours How-to[size=14.6667px]Model Files [size=14.6667px]The first model file shows all the pieces that are then isolated for your convenience into separate files. For some reason, when you upload OBJ to Thingiverse, objects are rotated 90 degrees (clockwise) around the X axis. Rotate -90 degrees in your slicer before printing. Of course, the two model files that are in the STL format (they come directly from Misan's model) are not rotated. Go figure... If you experience difficulties with the OBJ format, go to TinkerCad here, copy the project to your account and export to STL.
[size=14.6667px]Grocery list [size=14.6667px]Below are some searches on eBay that you could use for your own machine. I am not affiliated with any of the vendors that those searches may yield. Please proceed with caution on eBay. You will need:1 x CNC shield. Look for the ones with included jumpers. It's a drag when you don't have them and you need to configure microstepping. 1 x 12V power supply (the one I have is a quite beefy 12.5A, salvaged from another project) 4 x 8 mm diameter rods, any length you want (by pairs though). I used 2 x 400mm for X and 2 x 300 mm for Y (recycled from printers and scanners.) With these lengths, and the new Z stage, I get about 312(X) x 212(Y) x 23(Z) mm of workspace. 2 x X lengths of 10 mm (or 3/8") threaded rod, with associated bolts, washers and nuts 2 x pulleys (16 teeth, 5 mm bore) (you can also use 20 teeth with different grbl settings) GT2 belt: to know how much you need, add your X to your Y, multiply by two and add two inches for luck An assortment of M3 bolts in various length and their nuts For the Z stage:1 x 28BYJ stepper motor (5V or 12V) 1 x M5 bolt to secure the pen to the Z carriage
[size=14.6667px]Assembly [size=14.6667px]Before installing the stepper drivers on the CNC shield, install jumpers for microstepping. I installed all three jumpers on the three axis. Such precision may not be necessary for the Z axis. The 28BYJ can be 5V or 12V. It does not matter (see this article).
You may have to open the stepper to cut a trace on its PCB to disconnect the red wire (see here) and use: orange, pink, blue, yellow, in that order (blue, yellow, orange, pink should work too) Adjust the potentiometer on A4988 counter-clockwise until the motor runs but does not overheat ( check this article for details). The last model file and photograph show (hopefully) how it all fits together.
[size=14.6667px]grbl [size=14.6667px]You will need to re- compile grbl to activate CoreXY control. Before you compile, change config.h as such: #define HOMING_CYCLE_0 (1<<X_AXIS)
#define HOMING_CYCLE_1 (1<<Y_AXIS) // and this below goes uncommented
#define COREXY
[size=14.6667px]Control Software [size=14.6667px]
[size=14.6667px]grbl Settings (YMMV) [size=14.6667px]$4=0 (step enable invert, bool)
$5=0 (limit pins invert, bool)
$6=0 (probe pin invert, bool)
$10=3 (status report mask:00000011)
$11=0.010 (junction deviation, mm)
$12=0.002 (arc tolerance, mm)
$13=0 (report inches, bool)
$20=0 (soft limits, bool)
$21=1 (hard limits, bool)
$22=0 (homing cycle, bool)
$23=0 (homing dir invert mask:00000000)
$24=25.000 (homing feed, mm/min)
$25=500.000 (homing seek, mm/min)
$26=250 (homing debounce, msec)
$27=1.000 (homing pull-off, mm)
$100=96.000 (x, step/mm) or 80.000 if you used 20 teeth pulleys
$101=96.000 (y, step/mm) or 80.000 if you used 20 teeth pulleys
$102=814.000 (z, step/mm)
$110=20000.000 (x max rate, mm/min)
$111=20000.000 (y max rate, mm/min)
$112=2200.000 (z max rate, mm/min)
$120=200.000 (x accel, mm/sec^2)
$121=50.000 (y accel, mm/sec^2)
$122=200.000 (z accel, mm/sec^2)
$130=212.000 (x max travel, mm)
$131=312.000 (y max travel, mm)
$132=23.000 (z max travel, mm)
[size=14.6667px]Extensions and Derivatives [size=14.6667px]Thank you guys for your contributions!
|
发表于 2019-2-2 11:35:11