Standard Test Method for Determining A-Weighted Sound Power Level of Central Vacuum Power Units
https://www.astm.org/Standards/F2544.htm
Standard Test Method for Determining A-Weighted Sound Power Level of Central Vacuum Power UnitsActive Standard ASTM F2544 | Developed by Subcommittee: F11.25Book of Standards Volume: 15.08
| Format | Pages | Price | |  | PDF | 9 | $46.00 | [url=] ADD TO CART[/url] | | | 9 | $46.00 | [url=] ADD TO CART[/url] |
[/table]
Reprints and Permissions Permissions to reprint documents can be acquired through
Copyright Clearance Center [url=] [/url][url=]VISIT COPYRIGHT CLEARANCE CENTER  [/url]
[url=]Historical Version(s)[/url] - view previous versions of standard [url=]ASTM License Agreement[/url]
Significance and Use
4.1 The test results enable the comparison of A-weighted sound emission from central vacuum power units when tested under the condition of this test method.
1. Scope
1.1 This test method calculates the overall A-weighted sound power level emitted by central vacuum power units, intended for operation in domestic applications. This standard applies to the power unit only at the power unit location. To test the sound power level of a central vacuum at the user’s location, refer to Test Method F1334.
1.2 A-weighted sound pressure measurements are performed on a mounted central vacuum power unit in a semi-reverberant room. This test method determines sound power by a comparison method for small noise sources, that is, comparison to a broad band reference sound source.
1.3 This test method describes a procedure for determining the A-weighted sound power level of small noise sources. This test method uses a non-special semi-reverberant room.
1.4 Results are expressed as A-weighted sound power level in decibels (referenced to 1 pW).
1.5 The values stated in inch pound units are to be regarded as the standard. The values in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) [url=][/url]ASTM Standards [url=]C634[/url] Terminology Relating to Building and Environmental Acoustics [url=]E177[/url] Practice for Use of the Terms Precision and Bias in ASTM Test Methods [url=]E691[/url] Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method [url=]F820[/url] Test Method for Measuring Air Performance Characteristics of Central Vacuum Cleaning Systems [url=]F1334[/url] Test Method for Determining A-Weighted Sound Power Level of Vacuum Cleaners ANSI Standards S1.10 Method for the Calibration of Microphones
S1.43 Specifications for Sound Level Meters, IEC 804 and IEC 61672
S12.31
S12.32
S12.33 Engineering Methods for Determination of Sound Power Levels of Noise Sources in a Special Reverberant Test Room
Keywords A-Weighted Sound Power Level - Sound, Noise - Vacuum Cleaners
ICS Code ICS Number Code 17.140.20 (Noise emitted by machines and equipment); 97.080 (Cleaning appliances) UNSPSC Code UNSPSC Code 47121602(Vacuum cleaners)
Referencing This Standard[table=98%,transparent]
Link Here
Link to Active (This link will always route to the current Active version of the standard.)
DOI: 10.1520/F2544-11R18 Citation Format ASTM F2544-11(2018), Standard Test Method for Determining A-Weighted Sound Power Level of Central Vacuum Power Units, ASTM International, West Conshohocken, PA, 2018, www.astm.org
| 
发表于 2018-9-10 19:24:19
